---

Make Your Home Smart and Convenient with Shelly.

Shelly is a comprehensive smart home automation system designed to bring convenience, energy efficiency, and enhanced security to your living space. With a wide range of products, Shelly allows you to control lighting, climate, appliances, and security systems through an intuitive mobile app or voice commands. Whether you want to automate your daily routines, set up custom scenarios, or remotely monitor your home, Shelly’s devices offer seamless integration and easy installation. Compatible with various smart home ecosystems, Shelly provides a reliable and flexible solution for modern home automation.

Wave 1 (EU)

Device identification

Device: Wave 1 (EU)
EU Part number/Ordering Code: QNSW-001X16EU
Z-Wave Product type ID: 0x0002
Z-Wave Product ID: 0x0083
Z-Wave Manufacturer: Shelly Europe
Z-Wave Manufacturer ID: 0x0460

Terminology

• Device - In this document, the term “Device” is used to refer to the Shelly Qubino device that is a subject of this guide.

• Gateway (GW) - A Z-Wave™ gateway, also referred to as a Z-Wave™ controller, Z-Wave™ main controller, Z-Wave™ primary controller, or Z-Wave™ hub, etc., is a device that serves as a central hub for a Z-Wave™ smart home network. The term “gateway” is used in this document.

• S button - The Z-Wave™ Service button, located on Z-Wave™ devices and is used for various functions such as adding (inclusion), removing (exclusion), and resetting the device to its factory default settings. The term "S button" is used in this document.

Short description

The Device controls on/off function for one electrical appliance, e.g., bulb, ceiling fan, IR heater, electrical locks, garage doors, irrigation system, etc. The output contact is potential-free (dry contact), so different power supply loads (up to 16 A) can be connected to the Device. It is compatible with push-buttons and switches (default).

Switch/push-button connected to input terminal SW (SW1)

​
If the SW (SW1) is configured as a switch (default), each toggle of the switch will change the output O (O1) state to the opposite state - on, off, on, etc. If the SW (SW1) is configured as a push-button in the Device settings, each press of the push-button will change the output O (O1) state to the opposite state - on, off, on, etc.

Switch connected to input terminal SW (SW1)

If the SW (SW1) is configured as a switch (default), each toggle of the switch will change the output O (O1) state to the opposite state - on, off, on, etc.

• Change switch position once: Change the state of the output O (O1) state to the opposite state and send the command to the associated devices in associated groups 2 and 3 (check chapter Z-Wave Association).

Switch-memory connected to input terminal SW (SW1)

If the SW (SW1) is configured as a switch-memory, than:

• Switching to Close switch-memory contact: Change the state of the output state O (O1) to the On state and send command to the associated devices in associated groups 2 and 3 (check chapter Z-Wave Association)

• Switching to Open switch-memory contact: Change the state of the output state O (O1) to the Off state and send command to the associated devices in associated groups 2 and 3 (check chapter Z-Wave Association)

Push-button connected to input terminal SW (SW1)

If the SW (SW1) is configured as a push-button in the Device settings, each press of the push-button changes the output state O (O1) to opposite - ON, OFF, ON, etc.

• 1x click: Change the state of the output state O (O1) to the opposite one and send command to the associated devices in associated groups 2 and 3 (check chapter Z-Wave Association)

• 2x click: If the delay between first in second click is less then 500ms, this is interpreted as double clik. Send command to the associated devices (dimmers, shutters,….) in associated groups 2 and 3 (check chapter Z-Wave Association)

• Hold: Send command to the associated devices in associated group 3 (check chapter Z-Wave Association)

• Release: Send command to the associated devices in associated group 3 (check chapter Z-Wave Association)

Main applications

 

• Residential

 

• MDU (Multi Dwelling Units - apartments, condominiums, hotels, etc.)

 

• Light commercial (small office buildings, small retail/restaurant/gas station, etc.)

 

• Government/municipal

 

• University college

 

Integrations

Shelly Qubino Wave devices are developed on the world's leading technology for smart homes – Z-Wave®.

This means Shelly Qubino Wave works with all certified gateways supporting Z-Wave communication protocol.

To make sure the functions of Shelly Qubino Wave products are supported on your gateway, we are regularly executing compatibility tests of our devices with different Z-Wave gateways.

Simplified internal schematics

Device electrical interfaces

Inputs

 

• 1 switch/push-button input on screw terminal

 

• 1 potential-free contact relay input on screw terminal

 

• 3 power supply inputs on screw terminals: N (+), L (Ʇ) and 12V

 

Outputs

• 1 potential-free contacts relay output on screw terminal

Connectivity

Z-Wave - Unsecure, S0 Security, S2 Unauthenticated Security, S2 Authenticated Security

Safety features

Overheat protection

• switch off its own relay

• sends the Notification Report to the Gateway (Overheat detected)

• the led lights react as specified above (check blinking mode for Overheat detected)

Any of next activities reset this alarm: power cycle, short press on S button, press any switch-push button connected to any SW (SW, SW1, SW2, …) terminal.

NOTE: The Overheat protection is always active and cannot be disabled.
Additional description above under chapter Notification for Overheat detected.

Supported load types

 

• Resistive (incandescent bulbs, heating devices)

 

• Capacitive (capacitor banks, electronic equipment, motor start capacitors)

 

• Inductive with RC Snubber (LED light drivers, transformers, fans, refrigerators, air-conditioners)

User interface

 

S button and operating modes

• Settings mode:

Is required to start the desired procedure, for example: adding (inclusion), removing (exclusion), factory reset, etc. It has a limited operating time. After completing the procedure in Setting mode, the Device automatically switches to Normal mode.

• Entering Setting mode:

  • Press and hold the S button on the Device until the LED turns solid blue.

  • An additional quick press on the S button changes the menu in an infinite loop.

  • The Menu LED status has a timeout of 10s before entering again into Normal mode.

 

S button’s functions

• Manually adding the Device to a Z-Wave network

• Manually removing the Device from a Z-Wave network

• Factory Reset the Device

Specifications

Power supply	110-240 V AC / 24-48 V DC / 12 V DC ± 10%
Power consumption	< 0.3 W
Max. switching voltage AC	240 V
Max. switching current AC	16 A
Max. switching voltage DC	30 V
Max. switching current DC	10 A
Overheating protection	Yes
Distance	Up to 40 m indoors (131 ft.) (depends on local condition)
Z-Wave® repeater	Yes
CPU	Z-Wave® S800
Z-Wave® frequency bands	868,4 MHz; 865,2 MHz; 869,0 MHz; 921,4 MHz; 908,4 MHz; 916 MHz; 919,8 MHz; 922,5 MHz; 919,7-921,7-923,7 MHz; 868,1 MHz; 920,9 MHz
Maximum radio frequency power transmitted in frequency band(s)	< 25 mW
Size (H x W x D)	37x42x16 ±0.5 mm / 1.46x1.65x0.63 ±0.02 in
Weight	26 g / 0.92 oz.
Mounting	Wall console
Screw terminals max. torque	0.4 Nm / 3.5 lbin
Conductor cross section	0.5 to 1.5 mm² / 20 to 16 AWG
Conductor stripped length	5 to 6 mm / 0.20 to 0.24 in
Shell material	Plastic
Color	Blue
Ambient temperature	-20°C to 40°C / -5°F to 105°F
Humidity	30% to 70% RH
Max. altitude	2000 m / 6562 ft

Basic wiring diagram

Opens image in full screenOpen AC power supply

Opens image in full screenOpen 24 - 48 VDC power supply

Opens image in full screenOpen 12 VDC power supply

 

 

 

Our company was established in 2008 and is one of the leading CCTV cameras and equipment suppliers in Estonia and the Baltics. The most new models and technologies, the latest products from the most famous manufacturers of security equipment for video surveillance systems, and security systems can be found in the equipment catalog on our website.

About us
Contact us
FAQ
Cookie Policy
Privacy Policy
Terms of orders

Warranty and Returns
Tech Support
Payment / VAT free orders
Shipping and Delivery
News blog
Community poll

Enter a promo code you know and prices of coresponding goods will be automatically reduced

Keep up to date with new products and special offers

+372 55568231sales@megateh.eu

Cookie notice

This website uses cookies to ensure the best possible user experience.

Check our Cookie Policy